TX
Power transformer
Equipment transferring electrical power between winding circuits.
SLD / Schematic
Functional block · TII
Transformer inrush-restraint interface
Functional block · Substations
An independently authored application reference. The drawing shows the named function or circuit relationship; use the project legend and selected equipment documentation for its drafting form and connections.
Browse this installation focusIn plain English
What this block does
Identifies the measured or calculated inrush information used by the selected differential scheme.
A simple example
In a substation transformer bay, a protection panel receives winding-current measurements and equipment alarm contacts. An operator can then distinguish an electrical protection operation from a cooling-system or physical-condition alarm. For this reference, the drawing identifies “Inrush discrimination quantities” at the input and “Inrush restraint state” at the output. The method must match the selected relay application.
What the drawings help you do
Start at the named input: Inrush discrimination quantities. Identify its source device or document and the state represented on the drawing. Follow the named output: Inrush restraint state. Cross-reference its destination and separate the command from confirmation that the equipment responded.
- Input
- Inrush discrimination quantities
- Output
- Inrush restraint state
- Application reference
- An explanation of a named drawing function or circuit relationship; the project documents define the equipment and its connections.
Read the source: SEL-487E transformer protection relay
Schematic · TII
What it represents
Identifies the measured or calculated inrush information used by the selected differential scheme. Transformer monitoring interfaces connect physical sensors and protection calculations to the station's alarms and trip logic. Temperature, oil, gas, pressure and electrical measurements indicate different conditions and require separate interpretation.
In a substation transformer bay, a protection panel receives winding-current measurements and equipment alarm contacts. An operator can then distinguish an electrical protection operation from a cooling-system or physical-condition alarm. For this reference, the drawing identifies “Inrush discrimination quantities” at the input and “Inrush restraint state” at the output. The method must match the selected relay application.
Identify the sensor or calculation, its monitored zone and its assigned response. Alarm and trip thresholds, sensor fitting and protection settings belong to the selected transformer documentation and the approved protection design. The functional block is an independent explanation of this named application. Equipment-specific ratings, terminal connections and operating conditions must be established in the project documentation.
How to read it
- Start at the named input: Inrush discrimination quantities. Identify its source device or document and the state represented on the drawing.
- Follow the named output: Inrush restraint state. Cross-reference its destination and separate the command from confirmation that the equipment responded.
- The method must match the selected relay application.
- Identify the sensor or calculation, its monitored zone and its assigned response. Alarm and trip thresholds, sensor fitting and protection settings belong to the selected transformer documentation and the approved protection design.
Information to show or reference
- Label the source and connection reference for inrush discrimination quantities.
- Identify the destination and defined state of inrush restraint state.
- Record the equipment or control-document revision supporting this functional block.
- Check this application limit in the project design: The method must match the selected relay application.
A distinction that matters
The method must match the selected relay application. This reference describes the named application; it does not establish a new IEC graphical symbol, an ANSI device-function number or an exact manufacturer connection diagram.
Sources you can follow
These public references support the explanation and provide further detail. Their graphics and downloadable files remain with their publishers.
SEL-487E transformer protection relay
Public technical context for transformer protection and monitoring interfaces. Transformer protection, monitoring and measurement interfaces. The application text and educational graphic are independently authored; the publisher does not certify this representation.
About this graphic
This illustration was authored independently by Elora Grid to explain the concept. It is not reproduced from a customer drawing, an official standard graphic or a manufacturer CAD file. Its correspondence to an exact IEC or IEEE symbol identifier has not been certified.
SVG and DXF downloads contain this original artwork. Original artwork is available under CC BY 4.0. Third-party references retain their own terms.
Explore related references
87T
Transformer differential protection
Compares currents associated with a transformer protection zone using the selected relay's differential method.
Protection functions
TOMI
Transformer overexcitation measurement interface
Relates the transformer voltage and frequency inputs to its selected overexcitation supervision.
Functional block
Put the reference into a drawing workflow.
Elora Grid helps electrical teams work with drawings, specifications and equipment information. Explore the drafting workflow or join the early-access waitlist.