MIS
Microgrid interconnection switch
The switching device that separates a microgrid from the utility for islanding and reconnects it after synchronising.
SLD
Functional block · MPCG
Microgrid protection-group confirmation gate
Functional block · Microgrids
An independently authored application reference. The drawing shows the named function or circuit relationship; use the project legend and selected equipment documentation for its drafting form and connections.
Browse this installation focusIn plain English
What this block does
Confirms that assigned relays report the required operating group before dependent control proceeds.
A simple example
In a microgrid with sectionalized buses, the controller can associate each connected source and load group with its current island. A mode-dependent neutral or protection interface needs its own independently validated design. For this reference, the drawing identifies “Requested and reported groups” at the input and “Protection-group readiness” at the output. Relay coverage and transition behavior must be specified.
What the drawings help you do
Start at the named input: Requested and reported groups. Identify its source device or document and the state represented on the drawing. Follow the named output: Protection-group readiness. Cross-reference its destination and separate the command from confirmation that the equipment responded.
- Input
- Requested and reported groups
- Output
- Protection-group readiness
- Application reference
- An explanation of a named drawing function or circuit relationship; the project documents define the equipment and its connections.
Read the source: Microgrid operating modes and transitions management
Schematic · MPCG
What it represents
Confirms that assigned relays report the required operating group before dependent control proceeds. Microgrid topology control tracks which sources and load sections are electrically connected. The same physical installation can form several islands, so source roles, measurement boundaries and earthing interfaces must follow the established configuration.
In a microgrid with sectionalized buses, the controller can associate each connected source and load group with its current island. A mode-dependent neutral or protection interface needs its own independently validated design. For this reference, the drawing identifies “Requested and reported groups” at the input and “Protection-group readiness” at the output. Relay coverage and transition behavior must be specified.
Keep measured switch positions, logical island assignment and any earthing command separate. A conceptual topology block cannot establish a safe neutral-switching arrangement or prove that a circuit is de-energized. The functional block is an independent explanation of this named application. Equipment-specific ratings, terminal connections and operating conditions must be established in the project documentation.
How to read it
- Start at the named input: Requested and reported groups. Identify its source device or document and the state represented on the drawing.
- Follow the named output: Protection-group readiness. Cross-reference its destination and separate the command from confirmation that the equipment responded.
- Relay coverage and transition behavior must be specified.
- Keep measured switch positions, logical island assignment and any earthing command separate. A conceptual topology block cannot establish a safe neutral-switching arrangement or prove that a circuit is de-energized.
Information to show or reference
- Label the source and connection reference for requested and reported groups.
- Identify the destination and defined state of protection-group readiness.
- Record the equipment or control-document revision supporting this functional block.
- Check this application limit in the project design: Relay coverage and transition behavior must be specified.
A distinction that matters
Relay coverage and transition behavior must be specified. This reference describes the named application; it does not establish a new IEC graphical symbol, an ANSI device-function number or an exact manufacturer connection diagram.
Sources you can follow
These public references support the explanation and provide further detail. Their graphics and downloadable files remain with their publishers.
Microgrid operating modes and transitions management
Public technical context for microgrid topology and earthing coordination. Grid-connected and island modes, transitions, topology and authority. The application text and educational graphic are independently authored; the publisher does not certify this representation.
About this graphic
This illustration was authored independently by Elora Grid to explain the concept. It is not reproduced from a customer drawing, an official standard graphic or a manufacturer CAD file. Its correspondence to an exact IEC or IEEE symbol identifier has not been certified.
SVG and DXF downloads contain this original artwork. Original artwork is available under CC BY 4.0. Third-party references retain their own terms.
Explore related references
NER
Neutral earthing resistor
A resistor between a transformer or generator neutral and earth that limits earth-fault current to a set value.
SLD / Schematic
MATS
Microgrid alternate-PCC topology selector
Identifies which documented utility connection path currently defines the microgrid boundary.
Functional block
Put the reference into a drawing workflow.
Elora Grid helps electrical teams work with drawings, specifications and equipment information. Explore the drafting workflow or join the early-access waitlist.